StableBit Scanner not showing SMART Data when there is a SCSI to ATA Translation layer between the drives and the OS

[the1337moderate]

System Specs:

• Dell R720xd
• Server 2019 DataCenter
• 2x Dell H200e controllers
• Netapp DS4486
• Drives are mix of 8TB, 4TB, and 2TB

Controllers are running latest firmware. Stablebit Scanner will not pull SMART data from any drive. When attempting to "Show S.M.A.R.T..."  in StableBit Scanner the following message is displayed: "Using non-manufacturer specific interpretation rules."
 

Running smartctl will pull SCSI and ATA SMART data without issue (example of disk 17 shown):

 

C:\Program Files\smartmontools\bin>smartctl /dev/pd17 -x
smartctl 7.2 2020-12-30 r5155 [x86_64-w64-mingw32-2019] (sf-7.2-1)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               WDC
Product:              WD4001FFSX-68JDB
Revision:             4321
Compliance:           SPC-3
User Capacity:        4,000,787,030,016 bytes [4.00 TB]
Logical block size:   512 bytes
Physical block size:  4096 bytes
Logical Unit id:      0x50014ee65a754049
Serial number:        <redacted>
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Tue Sep 14 17:52:01 2021 CDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Disabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     31 C
Drive Trip Temperature:        60 C

Manufactured in week 04 of year 2010
Specified cycle count over device lifetime:  256
Accumulated start-stop cycles:  0
Read defect list: asked for grown list but didn't get it
Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0          0          0.000      120054
write:         0        0         0         0          0          0.000         186

Non-medium error count:        0

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -   36193                 - [-   -    -]

Long (extended) Self-test duration: 65535 seconds [1092.2 minutes]

scsiPrintBackgroundResults Failed [scsi response fails sanity test]
Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: power on
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=0 stp=0 smp=1
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x500a098006055e1e
    attached SAS address = 0x500a09800610033f
    attached phy identifier = 23
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: power on
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=0 stp=0 smp=1
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x500a098006055e1d
    attached SAS address = 0x500a0980060feeff
    attached phy identifier = 23
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0


C:\Program Files\smartmontools\bin>smartctl -d sat -A /dev/pd17
smartctl 7.2 2020-12-30 r5155 [x86_64-w64-mingw32-2019] (sf-7.2-1)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   197   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   149   138   021    Pre-fail  Always       -       11550
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       165
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   032   032   000    Old_age   Always       -       49885
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       159
 16 Unknown_Attribute       0x0022   119   081   000    Old_age   Always       -       2098043337661
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       153
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       746
194 Temperature_Celsius     0x0022   121   091   000    Old_age   Always       -       31
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       1

 

[Christopher (Drashna)]

You posted on another thread too. 

 

But You may need to enable the "Unsafe" "Direct IO" option to get the SMART data off of these drives, due to the controller. 
https://wiki.covecube.com/StableBit_Scanner_Advanced_Settings#Advanced_Settings

if that doesn't work, enable the "NoWmi" option for "Smart", as well.