Jump to content
Covecube Inc.

davidfowler2000

Members
  • Content Count

    5
  • Joined

  • Last visited

  1. Hi Christopher. I cannot really test this with the old server as it's been mostly emptied in order to move the drives in to the new server. It's not a major concern as it's getting decommisioned anyways. I'll enable logging on the new server and do transfers of large files and many smaller files with and without read striping enabled. I'll do it from the server to the PC over the network with SMB multichannel disabled (one network connection plugged) and two network connections to each machine. I'll use the same group of files and restart both machines between each test so there's nothing sitting in any caches.
  2. Yes. Putting files on to the server / pool is fine as I'm using a SSD to buffer incoming files. It's getting duplicated files back off the pool that is slow. I have since discovered unduplicated files are read normally whether read striping is on or off. I have been experimenting with local file transfers from the server's pool to it's own C:\ drive. Read striping enabled does not seem to slow down single large file transfers but it will only use one drive so the maximum transfer rate is the maximum of whatever disk it is coming from. Read Striping bar is 100% dark blue. (My interpretation of read striping is that it will transfer faster than the maximum drive speed as it can read from multiple sources but I am quickly figuring out that read striping is more for better access to lots of files at once.) Multiple small files are slowed down slightly. Photographs transferring at ~72MB/sec without striping, ~55MB/Sec with it enabled. Multiple drives being used. Read Striping Bar all 3 colours but mostly dark blue. Network transfers from the server to my PC: Read striping enabled causes single large files to transfer erratically. When the bar is 100% dark blue, it's only using one drive and transfers at 110MB/sec (network maximum) but when it starts going light blue up to 50% and using multiple drives, it slows right down to 45MB/sec. I have tried swapping out the Dell PERC H310 raid card for a HP H220 host bus card to no appreciable effect. So it seems to be there's a bottleneck appearing somewhere when the system is trying to use more than one hard drive at a time. I'll see if there's any firmware and / or driver updates for the PERC card and SAS backplane. Is there anything in Windows itself that may be causing this? Edit: There was an Intel chipset update. It improved single file transfers over the network although the transfer speeds are still erratic and slow when using multiple disks. But overall a bit better than before as it's not using multiple disks as much. Multiple small file copies with read striping enabled are now down to 10MB/sec using multiple drives or 80 - 90MB/sec with read striping disabled. Further experiments: I duplicated a folder with big files 3 times so it would go on to the SSD as well. Copying from that is fine with read striping enabled but it seems to be because it's mostly using the SSD. HDDs sometimes get used but doesn't cause any slow down. Remember the SSD is a M.2 drive on a PCI-Ex adapter card so it's not using the same interface as the HDDs.
  3. Hi Jaga. The files I am reading from the server are in a duplicated folder. The current set up is 2 SAS HDDs in a hot swap backplane and a SSD on a PCI-Ex card with the SSD Optimizer plugin so the data should be coming from the two HDDs. With read striping enabled, the Read Striping bar goes light blue and dark blue and you can see both drives being used in the activity panel. Mostly it's dark blue and very occasionally there's a little bit of light green. I disabled SMB multichannel on the server by unplugging one of the network cables. It made no difference. The old server doesn't have SMB multichannel. The 220MB/sec is from the SSD on my PC to the server pool with the SSD optimizer. On the old server it's 4 HDDs and 2 SSDs which will eventually make their way to the new server. Duplication enabled with some folders duplictaed 3 or 4 times. Both copies of DrivePool are release channel (downloaded from the main website). I tried an older version on the new server and it made no difference.
  4. I'm using DrivePool on my home server. It's a new machine to me, new install of Windows, latest version of DrivePool. DrivePool is running on the trial license until I copy the data off the old server and transfer the license. I first noticed this problem transferring data from the old server (latest DrivePool) to the new one via the network and when I tried transferring data from the new server to my PC I got the same thing. I'm using 2 x 1Gb network connections to get 2Gb via SMB multichannel. Transferring a single large file from the server runs at about 45MB/sec and transferring lots of smaller files like photographs runs at about 10MB/sec in bursts of 15 - 20 files with 2 or 3 seconds of inactivity between each burst. Turning read striping off gets me 110MB/sec for a large file and 60 - 70MB/sec for lots of little files. Transfers from my PC to the server run at about 220MB/sec until the SSD fills up. System is: Dell PowerEdge T320 Xeon E5-2407 24GB DDR3 ECC RAM Windows Server 2016 Essentials 2 x 2TB Toshiba hot swap SAS HDDs 1 x 256GB Plextor NVMe PCI-Ex SSD (Boot drive. 2 partitions - one for system, one pooled)
×
×
  • Create New...