AMCross Posted January 12, 2014 Share Posted January 12, 2014 hi this might be difficult to explain but here we go under scanner settings you can have the port number listed I have made sure that under my bios that I have the following port 0 hddvd/blu ray write port 1 system drive c/d port 2 data drive 1 port 3 data drive 2 port 4 data drive 3 port 5 data drive 4 all connected to the onboard intel sata controller they all show up correctly under scanner UNTIL my board also has 4 ports using the marvell controller so when I add another 3tb hard drive on port 0 of this controller scanner shows port 1 system drive c/d port 2 data drive 1 e port 3 data drive 2 f port 4 data drive 3 g port 0 data drive 5 h port 5 data drive 4 I is this a BUG ? Quote Link to comment Share on other sites More sharing options...
0 Christopher (Drashna) Posted January 12, 2014 Share Posted January 12, 2014 I'm not sure this is a bug. It looks like that you may have accidently click on the "Drive Letter" column and caused it to be sorted by drive letter. c/d, e, f, g, h, l. Instead of by port number, 0, 1, 2, 3, 4, 5. If this is the case (and I suspect that it is), don't feel bad at all. It took me a few minutes and a couple read through's to actually notice that. AMCross 1 Quote Link to comment Share on other sites More sharing options...
0 AMCross Posted January 17, 2014 Author Share Posted January 17, 2014 Christopher I also fell for the drive letter column when I first started using the product but this not the case here when I added another drive as a system backup I now get port 1 system drive c/d port 2 data drive 1 e port 3 data drive 2 f port 4 data drive 3 g port 0 data drive 5 h port 5 data drive 4 I port 8 system backup think scanner or drivepool is getting confused with two onboard sata controllers it should be port 0 blu ray writer (obviously not shown in scanner) port 1 system drive c/d port 2 data drive 1 e All ONBOARD INTEL port 3 data drive 2 f port 4 data drive 3 g port 5 data drive 4 h port 6 data drive 5 I ALL ONBOARD MARVELL port 7 system backup lets see what alex finds when he rdp into my system as it maybe related Quote Link to comment Share on other sites More sharing options...
0 Christopher (Drashna) Posted January 17, 2014 Share Posted January 17, 2014 Given what the error looks to be (related to Disk ID's), I suspect that the issue is definitely related. Quote Link to comment Share on other sites More sharing options...
0 AMCross Posted January 18, 2014 Author Share Posted January 18, 2014 still not 100% but much better will need to do some checking before I finally close this issue :-) still think scanner only works showing correct port when using one controller use two onboard controller and things get untidy will confirm in 24 hrs Quote Link to comment Share on other sites More sharing options...
0 Christopher (Drashna) Posted January 18, 2014 Share Posted January 18, 2014 Well, if you're going by disk number.... yeah, controller cards can mess that up. Quote Link to comment Share on other sites More sharing options...
Question
AMCross
hi
this might be difficult to explain but here we go
under scanner settings you can have the port number listed
I have made sure that under my bios that I have the following
port 0 hddvd/blu ray write
port 1 system drive c/d
port 2 data drive 1
port 3 data drive 2
port 4 data drive 3
port 5 data drive 4
all connected to the onboard intel sata controller
they all show up correctly under scanner UNTIL
my board also has 4 ports using the marvell controller
so when I add another 3tb hard drive on port 0 of this controller scanner shows
port 1 system drive c/d
port 2 data drive 1 e
port 3 data drive 2 f
port 4 data drive 3 g
port 0 data drive 5 h
port 5 data drive 4 I
is this a BUG ?
Link to comment
Share on other sites
5 answers to this question
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.